Exhibitor products

Especially in power plant operations but also in many other switchgear areas, active power for the optimization and control of processes must be continuously measured. The power converter AD-LU 410 GT is always adapted to the individual case by means of plant-specific adaptations. Due to the fully analog design, fast power measurements are possible, e.g. the detection of short-time load changes. The nominal voltage, the power to be measured and the desired output signal are required by the customer. The exact power values are available as standard signal for further processing.

The AD-LU 650 GT is a digital measuring transducers for the acquisition of all measured variables in the three-phase network. In addition to the fundamental oscillations, the harmonics up to the 32nd harmonic are also measured for currents and voltages. In addition to the three phase currents, the current in the neutral conductor can also be measured. Any measured variable can be assigned to each analog output. Each digital output can be assigned its own function such as limit value monitoring or pulse output for an energy meter. All measured data can be read out via the Modbus-RTU interface. With an optional display device such as the AD-MM 400 FE or the AD-MM 500 FE, the data can be displayed and the device can be configured if necessary.

The AD-STVEX 710 GVD supply isolating amplifier is used for the intrinsically safe supply of a transmitter installed in the hazardous area. The supply isolation amplifier itself is installed as associated electrical equipment in the non-hazardous area, i.e. the safe area. The signal is galvanically isolated and transmitted to the non-hazardous area. The passive input also allows active signals from the hazardous area. The active current output, the current sink output and the voltage output facilitate the adaptation to the following signal input. The device can be operated at 24 V DC or 230 V AC. Application Supply of a transmitter in the hazardous area and galvanic isolation of the signal. Specific characteristics - Supply of a transmitter up to zone 0 (gas) or 20 (dust) - Active current output, current sink output and voltage output - Open-circuit detection according to Namur recommendation NE43 - Further parameters configurable via configuration software AD-Studio - Detachable, coded connection terminals - Zero and full scale adjustment possible via front panel keys

The AD-SW 3 GL is used to measure high AC currents, such as secondary currents from large current transformers (e.g. 0...5A AC). The device contains 3 measuring transformers for contactless measurement of all three phase currents. The lines to be measured are fed horizontally through the device. Three small signal outputs are available for evaluation, which represent the measured current. The three output signals are galvanically coupled but separated from the input and the supply with high isolation. The AC sine wave voltage outputs, which follow the input signal 1:1 up to the maximum bandwidth of the device, can be customized. The integrated wide range power supply allows a wide supply voltage range with low self-heating.

The isolation amplifier AD-TV 420 GVD serves the galvanic separation of analogue signals and of transmitter signals. When a 2-wire transmitter is connected, this will be supplied directly via a galvanically separated and current-limited supply voltage. All measuring ranges and outputs can be freely parameterized. This can be carried out via the optional operating panel AD-VarioControl or via the programming software AD-Studio. The wide bipolar input measuring range makes this buffer amplifier into the universal type for almost all applications in the area of standard signals and beyond. All supply ranges are covered with the wide range power pack. Application Amplification, transformation and electrical isolation of current or voltage signals Specific characteristics - bipolar current input (+/- 0,5 mA bis +/- 50 mA) - bipolar voltage input (+/- 1 V bis +/- 100 V) - Power supply for 2- / 3-wire transmitters - 2 bipolar current or voltage output - Operating module as an accessory - 23 mm narrow housing with detachable terminal clamp

The digital multi-function measuring transformers of series VarioCheck AD-VC 1 are freely programmable digital measuring transducers with two analogue outputs and up to 2 limiting value relays. Extensive standard equipment and additional options solve almost all imaginable tasks of a modern evaluation. All measuring ranges and outputs can be freely parameterized. This can be carried out via the optional operating modul AD-VarioControl or via the programming software AD-Studio. VarioCheck AD-VC 1 fulfils all tasks of a universal and secure measuring value recording through integral function modules such as limiting value messages, freely adjustable hysteresis, selectable relay functions, time-delayed switching, automatic or manual simulation modus, free linearizing curves and a wide range of supply voltage.

The AD-VL 500 FE monitor module is a display unit and data logger for front panel installation. It has up to 8 analogue standard signal inputs. The inputs can be configured as current or voltage inputs. Counter values can be derived simultaneously from the analogue signals by means of adjustable switching thresholds. A scaled measured value display with freely definable units is possible. The display is done by freely configurable display elements such as numeric display, bar graph, time diagram, drag pointer, LEDs, etc. The unit is supplied with predefined standard display windows. All signals can be logged cyclically in the unit's own memory. The logged data are stored as daily files on an internal micro SD card. They can be retrieved at any time with a USB stick or downloaded via the network interface. The unit can be configured either via the integrated web server of the network interface or via the configuration software AD-Studio. The configuration software is available free of charge on the ADAMCZEWSKI website. The various interfaces (RS485/LAN) make it easy to integrate the device into your own data networks in order to read out measurement data in real time.

The ERO adjustment slides of the VS series are dovetail slides made of aluminum with maximum strokes (in the standard version) of 5 - 75 mm (depending on the size), which are manufactured in one, two or three-axis versions. The adjustment slides are available in 4 different types Their characteristics are the extensive opportunities of combinations and add-on options fore example 6 different clamping opportunities. A lasered scale on the side or a mechanical position display are standard options. If you like, you can get a customized adjustment slide for example with customized length.

The remote data transmission unit ADT1-Tube is encased in a robust, stainless steel housing, which is ideally suited to installation in 2" monitoring pipes. The LoRa module, which can be configured on a country-specific basis, establishes a connection with the Internet and makes it possible to collect measurement data in a low-cost and energy-saving manner. The ADT1 is also available with an NB-IoT / LTE-M radio module. These autonomous devices can be linked with digital level sensors and pressure transmitters in the KELLER Pressure D and X product lines. With three conventional, high-quality AA batteries, the system can operate autonomously for up to 5 years. The LoRaWAN provider can be selected freely or an in-house or open source infrastructure and associated services can be used. The easiest and most convenient way to access the collected data at the end of the transmission chain is via PressureSuite Cloud from KELLER Pressure.

Is your company faced with the challenge of developing highly complex systems that require precise integration of software, mechanics and processes? Our future-oriented automation solutions for existing or new systems and machines overcome the challenges in your production and increase efficiency and precision. We support you in the efficient design, programming and commissioning of complex systems. By using innovative architecture blueprints and drawing on our multidisciplinary expertise, we accompany your project step by step through to successful implementation. Our solutions are ideal for multi-axis systems in demanding production environments such as those required by machine tools and precision machines. Rely on our expertise and years of experience in this field to overcome your challenges and achieve high-quality results as quickly as possible. Through targeted project management and precise requirements management, we accelerate the path to successful project completion using digital models, virtual commissioning and seamless integration of these digital models into the operational phase. As we play a key role in the development of control systems, we can find the most efficient way to achieve the optimum for you. With our expertise, we intervene when you reach the limits of your automation solutions. Rely on the highly developed automation solutions from evosoft GmbH to future-proof your system and benefit from an increase in productivity, an improvement in quality, an increase in flexibility, a reduction in errors and costs and an increase in production speed.

"Advanced Flow" (AdvFlow) is an advanced planning and scheduling solution that supports complex planning processes in companies, in production, and in intralogistics. By utilizing artificial intelligence and machine learning, material flows are analyzed and optimized. Real-time data from plant and order management is used for continuous updating and optimization of the operational plan. The minimally invasive approach allows for direct implementation in ongoing operations, thereby reducing investments in costly modifications to existing systems and investments in new facilities.

Since 1953 – AGRO has been developing and manufacturing high-quality cable entry and cable installation products and systems, at its Hunzenschwil headquarters in Switzerland, for the mechanical engineering industry, for plant and equipment construction and for professional electrical installation work in buildings of all kinds. AGRO has been part of the KAISER GROUP since 2002, enabling our customers to benefit from the resulting synergies – both nationally and internationally.

A true innovation: Well-proven cable gland technology per EN 62444 in a cable entry unit for multiple cables. To date, the multiple-cable-entry solutions available on the market have proved unsatisfactory for many users. Either they do not achieve the required values in relation to sealing or strain relief, or their installation is time-consuming – a fact that quickly becomes apparent in the overall cost analysis. AGRO has been developing and manufacturing high-quality cable glands in accordance with EN 62444 for over 65 years. The know-how gained from this in relation to radial compression fabrication of sealing items is now being used for the fi rst time in cable feedthroughs. The specially-designed and reliable strain relief, together with the use of tested sealing units make MCE an innovative, extremely robust and dependable cable entry system. Multiple feedthroughs are widely used in various industries. They fi nd application where a number of cables are to be fed, close together. Compared to the use of numerous individual cable glands, the compact MCE solution saves space and users can benefi t from the effi cient, easily manageable installation process it facilitates – even where space is very limited. Fields of application include infrastructure projects (e.g. tunnels, IT data centres and telecommunication networks), control cabinet and plant construction, the processing industry, and vehicle, shipping, offshore and energy technology

The TURCK Intelligent Vision (TIV) AI camera brings artificial intelligence directly to the production line. The self-learning camera processes image data for code recognition, quality control, classification, or process monitoring locally and in real time—without additional hardware or complex programming.

Maximum user-friendliness combined with additional connection space AK small distribution boards from Spelsberg have for decades now proven to be suitable product solutions in highly-demanding installation situations, in particular in commerce and industry. Today they are characterised primarily by their flexibility, ease of handling, and more distributor space per housing, all with the highest level of reliability. New and further development of product lines are central to the Spelsberg corporate philosophy. Since they were brought onto the market in 1983, AK small distribution boards have demonstrated how challenging electrical installation applications call for special solutions. Spelsberg gives customers simply more values and, with these, the product solutions of choice for professional distribution in demanding environments. Challenging areas of application call for special solutions – that is what the AK small distribution board from Spelsberg stands for. For installations in commercial and industrial environments, this means: More connection space More reserves for retrofitting More air exchange More user-friendliness More flexibility by e.g. connection of up to four SCHUKO® sockets